Products

Fluorescent Linear (Zone 1) LFE/LFEE

LFE / LFEE-P series fluorescent light fittings are normally used in the chemical and petrochemical plants, off-shore platforms, refineries and any other industry where hazardous atmospheres (gas and combustible dust) are potentially present.

The LFE / LFEE-P range has been designed to meet the main requirements of illumination of working areas and to grant a safely evacuation of the plant in case of black-outs.

Unit Price:

Customers can still purchase even if there is no stocks available

Unit Of Measurement (UOM):

The materials used to manufacture the LFE - LFEE P series have been studied to grant the maximum protection against the highly corrosive agents present in these industries:

  • the body in glass fiber reinforced polyester (GRP), provides a very high mechanical strength together with a good resistance against the UV ray effects;
  • the transparent diffuser in UV ray resistance polycarbonate has a self-extinguishing property according to Standard UL 94;
  • the gasket on cover grants an IP66 protection level ;
  • the closing system in one single spot, apart from facilitating greatly the maintenance operations, is itself a guarantee of first-rate holding system since it provides a constant pressure of seals over all the perimeter of the diffuser ;
  • the internal electrical components are fully sealed to prevent any corrosive action that could cause electrical faults;
  • the body has two cable entries M25x1.5 on one side and one cable entry M25x1.5 on the opposite side so to allow any loop-in loop-out installation. On request it’s possible to have two cable entries M25x1.5 on both sides;
  • all the light fittings are equipped, as standard, with one cable gland and two stopping plugs in polyamide, Atex certified. Other materials or combinations are available as option;
  • two kinds of lampholder: G13 for traditional T8 fluorescent tubes and G5 for new generation of T5 fluorescent tubes;
  • electronic ballast, equipped with some self-protective functions, works with a multirange voltage and has a two-supply circuit design so to continue to energize one fluorescent tube in case the second one is faulty;
  • internal circuit is protected by fuses so to minimize any possible problems caused by over-voltage during normal operation;

LFE - P  Explosion proof Fluorescent Light Fitting

product
code

overall dimensions and weightfixing dimensionselectrical data
ABCkgblampholderpowervoltage
LFE 114P 698 222 145 4.8 400 M8 G5 bi-pin 1 x 14 W AC110 240V 50/60Hz
LFE 118P 698 222 145 4.8 400 M8 G13 bi-pin 1 x 18 W AC110 240V 50/60Hz
LFE 128P 1310 222 145 7.7 800 M8 G5 bi-pin 1 x 28 W AC110 240V 50/60Hz
LFE 136P 1310 222 145 7.7 800 M8 G13 bi-pin 1 x 36 W AC110 240V 50/60Hz
LFE 214P 698 222 145 5.0 400 M8 G5 bi-pin 2 x 14 W AC110 240V 50/60Hz
LFE 218P 698 222 145 5.0 400 M8 G13 bi-pin 2 x 18 W AC110 240V 50/60Hz
LFE 228P 1310 222 145 7.9 800 M8 G5 bi-pin 2 x 28 W AC110 240V 50/60Hz
LFE 236P 1310 222 145 7.9 800 M8 G13 bi-pin 2 x 36W AC110 240V 50/60Hz

LFEE - P Explosion proof Emergency Fluorescent Light Fitting

product
code

overall dimensions and weightfixing dimensionselectrical data
ABCkgbpower normalpower emergencyemergency time
LFEE 014P 698 222 145 6.6 400 M8 1 x 14 W 1 x 14 W 120 minutes
LFEE 018P 698 222 145 6.6 400 M8 1 x 18 W 1 x 18 W 120 minutes
LFEE 028P 1310 222 145 9.7 800 M8 1 x 28 W 1 x 28 W 120 minutes
LFEE 036P 1310 222 145 9.7 800 M8 1 x 36 W 1 x 36 W 120 minutes
LFEE 114P 698 222 145 6.6 400 M8 1 x 14 W 1 x 14 W 120 minutes
LFEE 118P 698 222 145 6.6 400 M8 1 x 18 W 1 x 18 W 120 minutes
LFEE 128P 1310 222 145 9.7 800 M8 1 x 28 W 1 x 28 W 120 minutes
LFEE 136P 1310 222 145 9.7 800 M8 1 x 36 W 1 x 36 W 120 minutes
LFEE 214P 698 222 145 6.8 400 M8 2 x 14 W 1 x 14 W 120 minutes
LFEE 218P 698 222 145 6.8 400 M8 2 x 18 W 1 x 18 W 120 minutes
LFEE 228P 1310 222 145 9.9 800 M8 2 x 28 W 1 x 28 W 120 minutes
LFEE 236P 1310 222 145 9.9 800 M8 2 x 36W 1 x 36W 120 minutes

The LFE-P series are used for the standard illumination while LFEE-P series are proposed with two different functions: “normal + emergency” or “only emergency” operation.

The LFEE-P “only emergency operation” can be supplied with diffuser showing different safety indications (EXIT, arrows, warnings, etc.) available, on request, also in local languages. The wiring diagram of LFEE-P series is designed to provide a continuous power supply to the emergency unit so to grant its full functionality anytime.

Besides a LED unit, well visible from outside, indicates the status of emergency unit through green/yellow/red colours to facilitate the maintenance activity. The internal wiring is designed to allow any combination of loop-in loop-out installation.

The light fitting can be installed using different mounting types: ceiling, chain, pendant, pole, and bracket.

The materials used to manufacture the LFE - LFEE P series have been studied to grant the maximum protection against the highly corrosive agents present in these industries:

  • the body in glass fiber reinforced polyester (GRP), provides a very high mechanical strength together with a good resistance against the UV ray effects;
  • the transparent diffuser in UV ray resistance polycarbonate has a self-extinguishing property according to Standard UL 94;
  • the gasket on cover grants an IP66 protection level ;
  • the closing system in one single spot, apart from facilitating greatly the maintenance operations, is itself a guarantee of first-rate holding system since it provides a constant pressure of seals over all the perimeter of the diffuser ;
  • the internal electrical components are fully sealed to prevent any corrosive action that could cause electrical faults;
  • the body has two cable entries M25x1.5 on one side and one cable entry M25x1.5 on the opposite side so to allow any loop-in loop-out installation. On request it’s possible to have two cable entries M25x1.5 on both sides;
  • all the light fittings are equipped, as standard, with one cable gland and two stopping plugs in polyamide, Atex certified. Other materials or combinations are available as option;
  • two kinds of lampholder: G13 for traditional T8 fluorescent tubes and G5 for new generation of T5 fluorescent tubes;
  • electronic ballast, equipped with some self-protective functions, works with a multirange voltage and has a two-supply circuit design so to continue to energize one fluorescent tube in case the second one is faulty;
  • internal circuit is protected by fuses so to minimize any possible problems caused by over-voltage during normal operation

certificate number: IECEx CML 17.0098X   CML 17 ATEX 1210X 
marking: Ex-proof Logo II 2GD Ex db e mb q IIC T4 Gb   Ex tb IIIC T83°C / T98°C Db
ambient temperature: -25°C +40°C   -25°C +55°C
degree of protection: IP66
conformity: Directive ATEX 2014/34/EU
standards: IEC-EN60079-0 / IEC-EN60079-1 / IEC-EN60079-5 / IEC-EN60079-7 / IEC-EN60079-18 / IEC-EN60079-31
category: suitable for Zone 1 – 2 (gas) and Zone 21 – 22 (dust)