Products

LED Floodlight (Zone 1) FLL

FL - FLL - FLP series floodlights are normally used in the chemical and petrochemical plants, off-shore platforms, refineries and any other industry where hazardous atmospheres (gas and combustible dust) are potentially present. The whole range has been designed to meet the main requirements of illumination of working areas.

Unit Price:

Customers can still purchase even if there is no stocks available

Unit Of Measurement (UOM):

The materials used to manufacture the FL, FLL and FLP series floodlights have been studied to grant the maximum protection against the highly-corrosive agents present in these industries:

  • body and cover in copper-free aluminium
  • external epoxy powder coating RAL 7001
  • window in thermoresistant glass sealed with auto-leveling silicone
  • gasket on covers in silicone granting an IP66 protection level
  • screws in stainless steel
  • one cable entry M25x1.5 on bottom side of Ex e terminal integrated box to allow a loop-in loop-out installation (models FL and FLL)
  • Ex e terminal integrated box to allow a direct installation on pole (model FLP)
  • all the light fittings are equipped, as standard, with one cable gland and one stopping plugs in polyamide, IECEx/Atex certified. Other materials or combinations are available on request

Special attention has been dedicated to reduce the heating: the external back-side of housing is fully provided with cooling ribs to facilitate the heat outflow.

code

overall dimensions

A1A2A3BCDE

øD

FL 520 680 330 460 198 93 70
FLL 520 680 330 460 135 93 70
FLP 520 635 400 128 62

FL series floodlights have a symmetric optic and are equipped with a complete range of control gears as Metal Halide, High Pressure sodium, and Induction so to satisfy different illumination requirements.

FLL and FLP series floodlights are equipped with LED granting the same illumination performation of conventional corresponding model but with the advantages typical of this technology such:

  • long-life duration (maintenance free)
  • energy saving
  • lower T classification allowing to be used with larger range of gases and dusts inside hazardous areas
  • good performance with vibrations due to LED solid-state light source
  • wide voltage range (AC 100 - 277 V) not influenced by voltage fluctations and good electromagnetic compability

The materials used to manufacture the FL, FLL and FLP series floodlights have been studied to grant the maximum protection against the highly-corrosive agents present in these industries:

  • body and cover in copper-free aluminium
  • external epoxy powder coating RAL 7001
  • window in thermoresistant glass sealed with auto-leveling silicone
  • gasket on covers in silicone granting an IP66 protection level
  • screws in stainless steel
  • one cable entry M25x1.5 on bottom side of Ex e terminal integrated box to allow a loop-in loop-out installation (models FL and FLL)
  • Ex e terminal integrated box to allow a direct installation on pole (model FLP)
  • all the light fittings are equipped, as standard, with one cable gland and one stopping plugs in polyamide, IECEx/Atex certified. Other materials or combinations are available on request

Special attention has been dedicated to reduce the heating: the external back-side of housing is fully provided with cooling ribs to facilitate the heat outflow.

certificate number: IECEx CML 17.0174X CML 17 ATEX 1319X

marking: Ex-proof Logo II 2GD Ex db ebop is IIB T3 /T4 /T5 Gb  Ex tb op is IIIC T85°C ~ T165°C Db

ambient temperature: -20°C +40°C / +55°C -

degree of protection: IP66

conformity: Directive ATEX 2014/34/EU

standards: IEC60079-0 / IEC60079-1 / IEC60079-7 / IEC60079-28 / IEC60079-31

EN60079-0 / EN60079-1 / EN60079-7 / EN60079-28 / EN60079-31

category: suitable for Zone 1 – 2 (gas) and Zone 21 – 22 (dust)

fl-01