Products

Fluorescent Linear (Zone 2) LFN

LFN -P series fluorescent light fittings are normally used in the chemical and petrochemical plants, off-shore platforms, refineries and any other industry where hazardous atmospheres (gas and combustible dust) are potentially present. The LFN -P range has been designed to meet the main requirements of illumination of working areas.

Unit Price:

Customers can still purchase even if there is no stocks available

Unit Of Measurement (UOM):

The light fitting is equipped with an interlock device. This can be mechanically connected with the internal Ex d safety switches, that automatically cut-off the power when the enclosure is opened.

LFN - P  Explosion proof Fluorescent Light Fitting

product
code

overall dimensions and weightfixing dimensionselectrical data
ABCkgblampholderpowervoltage
LFN 114P 698 222 145 4.9 400 M8 G5 bi-pin 1 x 14 W AC220-240V 50/60Hz
LFN 118P 698 222 145 4.9 400 M8 G13 bi-pin 1 x 18 W
AC220-240V 50/60Hz
LFN 128P 1310 222 145 7.8 800 M8 G5 bi-pin 1 x 28 W
AC220-240V 50/60Hz
LFN 136P 1310 222 145 7.8 800 M8 G13 bi-pin 1 x 36 W
AC220-240V 50/60Hz
LFN 214P 698 222 145 5.0 400 M8 G5 bi-pin 2 x 14 W
AC220-240V 50/60Hz
LFN 218P 698 222 145 5.0 400 M8 G13 bi-pin 2 x 18 W
AC220-240V 50/60Hz
LFN 228P 1310 222 145 7.9 800 M8 G5 bi-pin 2 x 28 W
AC220-240V 50/60Hz
LFN 236P 1310 222 145 7.9 800 M8 G13 bi-pin 2 x 36 W AC220-240V 50/60Hz

The LFN -P series fluorescent lighting fixture are available with two different bodies suitable for installation of single or double fluorescent tube to satisfy every illumination requirements inside hazardous areas classified as Zone 2 and /or Zone 22. The internal wiring is designed to allow any combination of loop-in loop-out installation. The light fitting can be installed using different mounting types as described in dedicated section of this catalogue.

The materials used to manufacture the LFN-P series have been studied to grant the maximum protection against the highly corrosive agents present in these industries:

• the body in glass fiber reinforced polyester (GRP), provides a very high mechanical strength together with a good resistance against the UV ray effects;

• the transparent diffuser in UV ray resistance polycarbonate has a self-extinguishing property according to Standard UL 94;

• the gasket on cover grants an IP66 protection level ;

• the closing system in one single spot, apart from facilitating greatly the maintenance operations, is itself a guarantee of first-rate holding system since it provides a constant pressure of seals over all the perimeter of the diffuser ;

• the internal electrical components are fully sealed to prevent any corrosive action that could cause electrical faults;

• the body has two cable entries M25x1.5 on one side and one cable entry M25x1.5 on the opposite side so to allow any loop-in loop-out installation. On request it’s possible to have two cable entries M25x1.5 on both sides;

• all the light fittings are equipped, as standard, with one cable gland and two stopping plugs in polyamide, Atex certified. Other materials or combinations are available as option;

• two kinds of lampholder: G13 for traditional T8 fluorescent tubes and G5 for new generation of T5 fluorescent tubes;

• electronic ballast, equipped with some self-protective functions, works with a multirange voltage and has a two-supply circuit design so to continue to energize one fluorescent tube in case the second one is faulty;

certificate number: IECEx CML 17.0099X CML 17 ATEX 4183X marking: ` II 3GD Ex d mb nA IIC T4 Gc Ex t IIIC T80°C Db ambient temperature: -25°C +50°C degree of protection: IP66 conformity: Directive ATEX 2014/34/EU standards: IEC-EN60079-0 / IEC-EN60079-1 / IEC-EN60079-15 IEC-EN60079-18 / IEC-EN60079-31 category: suitable for Zone 2 (gas) and Zone 22 (dust)